Choose a material

Roofing sheets

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

PIR insulation

A roof with Thermano Deck: substrate, vapour control and membrane

At a glance

A Thermano Deck roof works as an assembly of layers. The substrate must carry the loads, the vapour control layer must limit the ingress of vapour, and the membrane must drain water away. The durability of the system depends on their compatibility and on correctly made connections, not only on the parameters of the PIR core. Thermano Deck has a PIR core and a multi-layer, gas-tight facing containing aluminium on both sides. The product is intended, among other things, for classic flat roofs. When selecting PIR boards for the system, draw a large field of a flat roof based on trapezoidal sheet metal and finished with parapets in a real cross-section. Thermano Deck must be selected together with the vapour control layer, the substrate and the method of executing the waterproofing, because the other layers must match the same solution.

Pale core and red-grid facing, illustration for the Thermano Deck insulation layer

Product construction in the context of the system

The individual layers must work together, because the name of the roofing product alone does not determine how all the layers are joined. The adopted set should make it possible to achieve a repeatable roof cross-section before the work is divided into successive sections. In the description of the solution, add the type of substrate, the arrangement of the protective layers and the selected method of fixing the thermal insulation, so that the complete set of layers can be verified.

Support and method of connection

Thermano Deck boards have a BASIC, TOP or MASTER edge, and the standard external dimension is 1200 × 2400 mm. The edge variant affects the row layout and the method of covering, so the choice must be linked to the setting out of the roof slope.

Continuous polyurethane insulation requires a correct detail; in the description, include the arrangement of the boards with the longer side perpendicular to the ribs of the trapezoidal metal deck. The row layout should result from the coverage of the ordered TOP or MASTER edge before the layout is considered ready for execution. The instructions for the full field do not cover all terminations, because the difference between the external dimension and the coverage increases with successive rows. The installation drawing should allow the roof to be set out according to the selected edge profile and to achieve a predictable completion of the field. Before you accept a substitute, check the direction of the ribs, the actual coverage of the ordered boards and the support of the cut pieces at the parapet in relation to the adjacent layers.

TOP and MASTER in Thermano Deck should not be treated as an identical overlap variant. They have different coverage dimensions stated in the product documentation. When the project sets out specific rows, changing the edge requires the layout to be checked again. The difference must also be taken into account for the last strip at the parapet. The roof system consists of the actual dimensions of the components, not just their common trade name.

Compatibility of the protective layers

Thermano Deck requires a dry and level substrate and a proper vapour control layer. On trapezoidal metal decking, the longer side of the board is laid perpendicular to the ribs, which links the board layout to the direction of support.

When selecting the protective layers, discuss the connection of the vapour control layer at the point where the work stage changes on a large industrial roof. The unclosed perimeter of the thermal insulation must be protected against water and the flow of moist air, because airtightness must also be achieved at the connections between different parts of the system. In the completed building element, the polyurethane foam needs protection, because the silver surface of Thermano Deck does not replace the continuity of a separate vapour control layer. The adopted detail must allow installation to proceed so that completed sections do not take in water from the part still open. In the description of the installation sequence, indicate the tightness of the temporary termination, the dryness of the substrate and the condition of the material after a break in the works; this information should be consistent with the documentation for the entire set.

Thickness matched to the assembly

The lambda of Thermano Deck is 0.023 W/(m·K) for thicknesses of 30–90 mm and 0.022 W/(m·K) for 100–200 mm. Thermal design must therefore assign the value to the specific thickness range, not to the product name alone.

In the system calculation, include a comparison of 90 mm and 100 mm boards lying on either side of the threshold of the declared lambda. For the selected Deck thickness, the correct lambda of 0.023 or 0.022 W/(m·K) must be retained so as not to combine parameters from different material variants. A mere change of material name does not give equivalence, since using one value for both variants will distort the assessment of the difference in their thermal resistance. When comparing polyurethane boards in alternative configurations, the change in insulation performance must be calculated without omitting the ranges listed in the product data sheet. In both variants, compare the RD values of the selected thicknesses and the influence of fasteners and adjacent layers on the roof result for the same function of the building element.

Range of mechanical and fire parameters

When selecting Thermano Deck, check the compressive stress assigned to the thickness: a minimum of 150 kPa at 10% deformation applies to boards of 30–160 mm, and a minimum of 120 kPa to boards of 170–200 mm. A change in thickness can therefore change the data needed to assess the support of subsequent layers. The test result is not the permissible roof load. The reaction to fire class of the product is E.

The summary of requirements for the system should explain the 160 and 170 mm variants, for which the declared level of compressive resistance changes. The CS value must be read for the specific thickness range of the Thermano Deck board, and the assessment range must correspond to the actual configuration of the building envelope. The significance of the parameters changes with the assessment range, because a thicker Thermano Deck board does not necessarily have a higher CS value than a thinner one. Before approving the structure, the mechanical requirements must also be maintained even when the thickness is increased for thermal reasons. In the application documents, look up the declaration range for the specific thickness and the method of transferring loads from the planned equipment, and compare them with the designed layers.

Complete specification for pricing

Base the order of Thermano Deck on three pieces of information: the type of substrate, the edge variant and the planned covering. If the roof is to have PV, also indicate the method of mounting the installation, because it affects the load distribution and the detail around the bases. This information allows the board to be linked with the vapour control layer and the waterproofing into a single system.

When pricing the item “polyurethane insulation”, analyse the demand for boards together with the work around drains, parapets and installation bases. The offers being compared must cover the same work at drains, parapets and installations, so that the scope of purchase corresponds to the complete specification of the solution. An omitted item may come back as additional work, because the cost of details may remain similar despite a small change in the price of material on the main field. A well-described scope allows offers with the same scope of protection, fixing and finishing of the covering to be compared. On acceptance of the delivery and the works, confirm the number of boards in the selected edge profile, the quantity of auxiliary materials and the responsibility for flashings, so that they match the agreed system.

7 branches. Materials closer to your project.

Sandwich-panel.pl map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]

Check prices and availability: +48 500 409 109

Free quote

Materials for your project