Choose a material

Roofing sheets

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

PIR insulation

Thermano ETICS at parapets and eaves: joining wall and roof insulation

At a glance

At the roof edge, the façade must combine thermal protection with protection against water. Thermano ETICS must be brought to this point in accordance with the design. The division of work between the façade team and the roofing team should not leave an open gap or an unprotected edge of insulation. Thermano ETICS is a composite board consisting of PIR with an outer EPS layer 20 mm thick. The PIR part has gas-tight multilayer facings incorporating aluminium. When selecting PIR boards for the system, draw the cross-section of the façade board with a PIR core and an outer EPS layer 20 mm thick in the actual cross-section. The surface of Thermano ETICS must be recognised as the outer EPS layer belonging to the composite, because the remaining layers must match the same solution.

Two board sections with speckled EPS faces, accompanying the Thermano ETICS guide

Product construction in the context of the system

The individual layers must work together, because the visible EPS is part of the composite and not a freely selectable substitute layer. The adopted set should allow the construction of Thermano ETICS to be preserved from the core to the surface prepared for further works. In the description of the solution, add the full product name, the side with the EPS layer and the compatibility of the intended façade finish, so that the complete set of layers can be verified.

Support and method of connection

The Thermano ETICS board is available in a 600 × 1200 mm format with BASIC edges; the variants of overall thickness range from 100 to 180 mm. The dimension and edge must be carried over into the layout drawing, because the division of the plane at the parapet and eaves depends on them.

Continuous polyurethane insulation requires a correct detail; in the description, include the arrangement of the 600 × 1200 mm rectangles at the corners of façade openings. The course of the joints at the corners of openings must be established before laying the BASIC boards begins, before the layout is considered ready for execution. The instructions for the full field do not cover all terminations, because the wall area alone does not show the number of cut pieces needed where windows are closely spaced. The installation drawing should make it possible to plan the thermal insulation so that the execution of the reinforcement does not rely on a random board layout. Before you accept a substitute, check the layout drawing of the elements and the way the composite is terminated at the window frames in relation to the adjacent layers.

Thermano ETICS has an outer EPS surface, so the description of the detail should preserve this construction. This is not the same situation as the direct finishing of any PIR board with a different facing. At the edge of the opening, the termination of the entire composite must be resolved. The fixing and the reinforced layers are assessed separately. Any simplifications should follow from the documentation of the system used, and not from a similar core colour.

Compatibility of protective layers

The 20 mm EPS layer forms the upper part of Thermano ETICS and immediately prepares the substrate for the subsequent layers of the façade system. Nevertheless, at the window sill, the plinth and the top termination of the wall, water still requires separate drainage.

When selecting the protective layers, address the junction between the window sill and the façade, through which water could get behind the finishing layer. The window sill and the top termination of the wall should drain water away from the surface and the interior of the thermal insulation, because tightness must also be achieved at the connections between the different parts of the system. In the completed building element, the polyurethane foam needs a covering, because an additional 20 mm of EPS does not remedy a leaky flashing or the lack of a fall on the window sill. The adopted detail must allow water to be drained away from the surface and the interior of the insulated wall. In the description of the installation sequence, indicate the projection and terminations of the window sill, the closing of the sides and the continuity of the seal at the window; this information should be consistent with the documentation for the entire set.

Thermal effect of the entire building envelope component

The value of 0.023 W/(m·K) applies to the PIR part, not to the entire board. The insulating performance of Thermano ETICS is therefore read from the thermal resistance R given for the composite, not from the lambda of the core alone.

When calculating the system, take into account the thermal resistance of the composite, in which PIR and EPS have different conduction properties. The thermal resistance of Thermano ETICS must be assessed taking into account the different properties of the PIR and EPS parts, so as not to combine parameters originating from different material variants. A mere change of material name does not give equivalence, since the figure of 0.023 W/(m·K) describes the PIR part and is not the lambda of the entire board thickness. When comparing polyurethane boards in alternative configurations, Thermano ETICS must be compared with another solution on the basis of the R of the finished product. In both variants, compare the total thickness of the variant and the corresponding thermal resistance value of the composite for the same function of the building element.

What the assessment of the entire solution covers

The declared reaction to fire of Thermano ETICS relates to the product and is E. However, the finished façade is determined by the entire system, so the assessment must also cover the fixing, the reinforcing layer and the render. The product alone does not determine the behaviour of the complete building element.

The schedule of requirements for the system should clarify the assessment of the finished façade, in which the Thermano ETICS board itself has reaction-to-fire class E. The composite should be assessed together with the fixing, the reinforcing layer and the render of the given system, and the scope of the assessment must correspond to the actual configuration of the building element. The significance of the parameters changes with the scope of the assessment, because the product class cannot be replaced by a random result found for another ETICS system. Before the design is approved, the required layer arrangement and its documentation must be established. In the application documents, look up the set of system components, the fixing design and the conditions for the correct fire assessment, and compare them with the designed layers.

Complete specification for pricing

In the order for Thermano ETICS, state the full product name and the total thickness of the composite. A comparative offer is reliable only if it covers the same façade finish system. Otherwise you are comparing items with a different scope.

When pricing the item “polyurethane insulation”, analyse the full specification of the Thermano ETICS composite with its total thickness. The full name and thickness of Thermano ETICS must be agreed together with the scope of the façade finish, so that the scope of purchase corresponds to the complete specification of the solution. An omitted item may come back as additional work, because a similar trade description does not guarantee that the products being compared have the same construction. A well-described scope allows a comparable price to be obtained while retaining the specific Thermano ETICS variant. On acceptance of the delivery and the works, confirm the name and thickness of the board, the scope of the finish system and the quantity of materials needed at openings, so that they match the agreed system.

7 branches. Materials closer to your project.

Sandwich-panel.pl map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]

Check prices and availability: +48 500 409 109

Free quote

Materials for your project