Choose a material

Roofing sheets

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

XPS insulation

XPS and industrial floor drainage: connecting insulation to outlets

At a glance

The drainage channel interrupts the straightforward arrangement of the floor layers. At this point, the drain must be accommodated, its support ensured and tightness maintained. XPS helps to limit heat losses beneath the floor finish, but it must not obstruct drainage or take on structural functions that were not provided for in the design. The extruded polystyrene must be matched to the finished detail. Cutting the boards at random around the gully usually leaves too many unknowns. Water flows over the surface with which it is in contact. Therefore, the fall of the finished floor must lead to the drain without local ponding. Simply laying XPS on a sloping substrate does not guarantee correct drainage of the finished floor. The thicknesses of all layers, the level of the frame and the requirements for the load-bearing layer must be coordinated.

Close-up of a grey XPS board with a rebated edge and a second board in the background

The fall must be established on the correct layer

On the plan, it is worth marking the washing areas, gates and zones exposed to liquid spills. Each of these may require a different pattern of falls. XPS is selected for the cross-section after these levels have been established. The thickness of the structural concrete at the channel should not be reduced merely to keep the insulation thickness unchanged. A change of cross-section requires the designer’s approval.

The drain needs stable support

A gully or channel can carry loads from vehicular traffic. Its installation must correspond to the intended mode of use. The extruded polystyrene next to it is not automatically a substrate for fixing the device. The way forces are transferred from the grating and body to the floor structure and the layers beneath must be verified.

The edge zone of the channel is particularly important. Uneven support can promote displacement and damage to the junction with the floor finish. Using stronger XPS does not repair a poorly installed drainage outlet. The design specifies where the insulation can be continuous and where a separate detail must be introduced. The assessment covers the entire assembly, not just a single insulation board.

Low water absorption does not create a seal

XPS limits water absorption thanks to its cellular structure. However, water can pass through a gap at the drain body or through the junction between layers. The basis of tightness is a properly designed waterproofing system. Its connection to the drain must be provided for the specific set of materials and operating conditions, including possible floor cleaning.

Extruded polystyrene will not replace a flange, a seal or a compatible connection of the coating to the drain. Likewise, an overlap at the edge of the XPS is not a watertight joint. At acceptance, the thermal insulation and the continuity of the water protection must be checked separately. Flooding the surface can be part of the inspection only if the technology permits it and a safe method of carrying out the test has been prepared.

Cutting boards without accidental voids

Around the drain, the XPS usually has to be adapted to an irregular layout. First the outline is marked out, then precise cuts are made. An excess of large gaps makes it difficult to maintain continuous insulation and even support. The infill is selected according to the design and the material instructions. It should not create a hard, random point beneath the load-bearing layer.

Drain pipes also require a planned space. It cannot be assumed that an arbitrarily deep channel cut into the XPS will leave sufficient support for the floor. Extruded polystyrene must be considered together with the routing of the services. If the pipe run forces a change in the height of the layers, it is best resolved on the drawing. Corrections made during concreting are much harder to check.

Process water also means chemical composition

In some halls, drains carry away water after equipment or surfaces are washed. In that case, the compatibility of the materials used with the agents employed is important. XPS should not come into contact with preparations that damage polystyrene. This also applies to installation materials. Compatibility information must be obtained for the specific adhesive, primer or sealant.

There is no need to attribute to the insulation resistance to a liquid that, under correct operation, remains in a sealed channel. However, a possible failure and the way it is detected must be considered. XPS covered by concrete is difficult to inspect without interfering with the floor. Access to the drains, cleaning and checking the connections limit the risk of a long-term leak. This is a practical element of maintaining the entire floor.

Acceptance of the interface between several trades

Well-known XPS manufacturers include Austrotherm, Synthos and HOCH. Products should be compared according to the required properties and intended use. The colloquial word styrodur does not specify the permissible load at the drain or the reaction to installation materials. In the specification it is worth combining the requirements for the insulation with the drawing of the channel bedding, so that every crew works to the same version.

Before covering, the levels, the support of the drain, the fit of the XPS and the continuity of the waterproofing are checked. It is worth establishing who accepts the interfaces between the building works and the installation works. Extruded polystyrene will fulfil its thermal function if it remains part of a correctly executed system. A properly functioning drainage system should not require guessing where the water passes under the finished floor.

7 branches. Materials closer to your project.

Sandwich-panel.pl map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]

Check prices and availability: +48 500 409 109

Free quote