About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

Where to look for corrosion on metal roofing and how to prevent it

Protecting a metal roof from corrosion starts with the choice of coating, which should be matched to the local environment before the sheets reach the site. Check the type of metallic layer and organic coating, and assess the suitability of the outer and inner faces separately, particularly with a damp or aggressive interior. Colour alone is not enough. Also confirm that the profile and thickness suit the structure and that the protection suits the surrounding conditions. Long-term durability then depends on correct installation, water drainage and control of condensation.

By |2026-11-15T03:31:39+01:002025-09-10|Construction basics|Comments Off on Where to look for corrosion on metal roofing and how to prevent it

How should supports be selected for a panel wall exposed to wind?

Supports should not be positioned solely for the convenience of column layout. A wall panel carries wind pressure and suction, and its deflection affects both appearance and the performance of connections. The correct spacing results from the loads and the data for the specific product. The number of spans, the width of supports and the parameters of both steel facings are also important. A single panel may rest on two or more supports. The distance between adjacent supports is the span. In the tables, single-span and multi-span arrangements have separate conditions. A more favourable result cannot be selected without conformity with the actual frame.

By |2026-11-14T12:37:14+01:002025-09-06|Construction basics|Comments Off on How should supports be selected for a panel wall exposed to wind?

Tile-effect or trapezoidal steel roofing: which suits the roof?

The choice between a tile-effect metal sheet and trapezoidal sheeting depends primarily on roof pitch and geometry, not on the price per square metre of the sheet alone. Check the specific profile's conditions of use – requirements for laps and layers beneath the covering vary between products. Compare complete roof systems serving the same function, including support, coating and full cost. On complex roof slopes, lay out the sheets to assess cutting and waste. Ultimately, choose the solution that meets technical requirements and suits the building.

By |2026-11-14T16:29:21+01:002025-08-29|Construction basics|Comments Off on Tile-effect or trapezoidal steel roofing: which suits the roof?

Choosing a plot for a steel building – checks before placing an order

A rectangle for the hall fits on the plot. That is a good start, but not yet proof that the investment will be possible and convenient. Access, space for handling, access to utilities and suitable ground are needed. Planning conditions and the required construction procedure must also be established. Ordering the steel structure before this survey can lock the investor into dimensions that cannot be reasonably used. Check the local plan provisions for the specific plot. The permitted function of the building and its siting conditions matter. A warehouse hall, workshop and production plant may impose different requirements. The mere presence of a similar building in the neighbourhood does not determine whether construction is possible. A steel hall must comply with the rules applying to the given area.

By |2026-11-15T03:32:25+01:002025-08-26|Construction basics|Comments Off on Choosing a plot for a steel building – checks before placing an order

How can two lines of insulated wall panels with a mineral wool core differ?

The names of lines of insulated wall panels with a mineral wool core do not form a common quality scale. A term suggesting a stronger or better version may refer only to a selected feature. In a small practice, what matters most is whether a specific variant meets the wall requirements. So compare the data and conditions of use rather than treating the name as a ready answer. Variants may differ in core density, facing thickness or joint design. Sometimes special seals are added, and at other times the range of available dimensions changes. Each such difference can affect other properties. A higher price does not yet say which of them is important for the planned premises.

By |2026-11-14T10:16:33+01:002025-08-21|Construction basics|Comments Off on How can two lines of insulated wall panels with a mineral wool core differ?

Selecting rooflights for homes and industrial buildings

First decide whether the light is meant for specific workstations or for even illumination across a whole zone — this determines the choice between a continuous strip and point rooflights. It is also worth settling whether the element should only admit light or also provide ventilation or smoke exhaust. Check how the rooflight interfaces with the sandwich panel and whether the opening is allowed for in the design. Pay attention to the thermal performance of the whole junction, the risk of condensation and the required roof pitch. Agree the opening size with the designer before ordering panels and structural components.

By |2026-11-15T03:30:59+01:002025-08-18|Construction basics|Comments Off on Selecting rooflights for homes and industrial buildings

PIR in wall assemblies: external insulation systems, cavities and protective layers

A wall with PIR can be finished in various ways. Each of these requires a different connection between the board and its surroundings. Render, the façade supporting substructure and the protective layer of the wall do not perform the same function. The choice of insulation must therefore begin with the complete cross-section. PIR boards can form a continuous insulation layer on the outer side of the wall. This position helps to limit thermal bridges associated with structural elements. The continuous outer layer should extend to the insulation of adjacent building components. A drawing of a flat section of wall is not sufficient to assess the terminations. The connection at the floor slab may have a different geometry from the regular field.

By |2026-11-16T01:34:47+01:002025-08-17|Construction basics|Comments Off on PIR in wall assemblies: external insulation systems, cavities and protective layers

Matt or gloss? Choosing the finish for tile-effect metal roofing

The choice between matt and gloss is determined mainly by how the roof is to reflect light, not by durability alone. Both finishes are available in different coating systems, so the material's parameters and intended use should be checked first, with appearance assessed afterwards. It is worth viewing a sample outdoors at an angle close to the roof pitch, because the same colour can look different depending on texture and lighting. Matt usually diffuses reflections and gives the roof a calmer appearance, while gloss more strongly emphasises the curves of the profile. The final decision should take account of both aesthetics and the conditions of use.

By |2026-11-14T23:25:00+01:002025-08-14|Construction basics|Comments Off on Matt or gloss? Choosing the finish for tile-effect metal roofing

How to prepare for and carry out the installation of insulated roof panels?

A weathertight roof is created from well-selected panels, suitable supports and carefully executed joints. Simply screwing down successive elements is only part of the task. Before installation, the laying direction, the lifting method and the water drainage details must be established. The sequence below organises the work, but the joint dimensions depend on the specific system. Verify the axes, the plane and the support widths, as well as the conformity of the structure with the design. Crooked purlins can cause poor bearing and stress on the panels. The structure should not be straightened by over-tightening the cladding with screws. Before starting the cladding, also confirm the stability of the frame and the completion of works that could damage the coatings.

By |2026-11-14T12:35:50+01:002025-08-08|Construction basics|Comments Off on How to prepare for and carry out the installation of insulated roof panels?

How do you calculate the cost of a sandwich panel roof from roof slope to gutter?

The cost of a sandwich panel roof consists of many items, although the rate for the panel usually attracts the most attention. You also need to calculate the actual roof slope, the cutting layout, the joints, the flashings and the crew's work. A detailed schedule allows you to compare quotes for the same roof and to see whether an attractive price omits part of the required scope. The length of the roof slope is measured in the direction of the fall, taking into account the eaves detail and the joints. The area of the horizontal projection may differ from it. On the drawing, also mark openings, skylights and points of contact with other elements. Do not automatically deduct them from the purchase, because an opening is often cut from a full panel.

By |2026-11-14T12:36:57+01:002025-08-08|Construction basics|Comments Off on How do you calculate the cost of a sandwich panel roof from roof slope to gutter?