About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

How to restore the appearance of a metal roof

Start by washing a small section of the sheeting to see whether cleaning alone will do or whether a local coating repair is also required. Assess the kind of soiling and the state of the finish, since dust, plant debris, coating ageing and corrosion each call for different treatment. Pay particular attention to spots beneath trees, beside the chimney and in the valleys, where dirt may be concentrated. If you notice flaking, detachment or rust, determine whether it involves just the top layer or the steel beneath as well.

By |2026-11-14T19:54:19+01:002025-10-12|Construction basics|Comments Off on How to restore the appearance of a metal roof

Thermano Roof in the roof assembly. Fixing, covering and support

Thermano Roof can be used in various roof assemblies, but each has its own rules. A bonded assembly requires a different assessment of the joints than a mechanically fixed one. The board's parameters are part of the selection, alongside the compatibility of the covering and the preparation of the substrate. Thermano Roof is a rigid PIR board with a gas-tight multilayer aluminium facing on both sides. The manufacturer specifies it for, among other things, flat roofs and above-rafter insulation. When selecting PIR boards for an assembly, draw the pitched roof slope on which the insulation is to sit above the wooden rafters in the actual cross-section. The Thermano Roof layer above the rafters must be connected to the terminations at the eaves and openings, because the remaining layers must fit the same solution.

By |2026-11-16T01:35:23+01:002025-10-11|Construction basics|Comments Off on Thermano Roof in the roof assembly. Fixing, covering and support

termPIR MAX 19 AL in roof design: thermal performance, geometry and loads

In a roof, thermal insulation cannot be separated from the parapet height and the drainage layout. termPIR MAX 19 AL can help to reconcile these requirements. At the same time, the fixing and the permissible loads of the entire building envelope must be fully verified. termPIR MAX 19 AL is a board made of rigid PIR foam, protected on both sides with a gas-tight laminate of aluminium, paper and polyethylene. Its key distinguishing feature is its level of thermal conductivity. When selecting PIR boards for the assembly, draw the point at which little space remains for the insulation under the existing flashing in the actual cross-section. The cross-section at the existing flashing must be checked before taking advantage of the low lambda value, because the remaining layers must fit the same solution.

By |2026-11-16T01:35:05+01:002025-10-10|Construction basics|Comments Off on termPIR MAX 19 AL in roof design: thermal performance, geometry and loads

Weatherproof chimney flashings on a metal roof

A watertight chimney flashing depends above all on correctly shaped detailing, not merely on sealing with mastic. The building owner and the contractor should check whether the solution accounts for the actual roof geometry, the sheet profile and the ability of the chimney to move relative to the slope. Support, correct laps and the connection to the underlay are key. It is also worth assessing whether the detail can later be inspected and maintained, especially on the upper side where leaves and snow collect.

By |2026-11-14T23:27:43+01:002025-10-08|Construction basics|Comments Off on Weatherproof chimney flashings on a metal roof

What should you do after spotting a roof leak?

After noticing a roof leak, first limit damage inside the building and ensure safety rather than immediately searching for the source above the stain. Water can travel along roof components, so the wet patch need not lie beneath the leak. Check whether the problem occurs during ordinary rain, strong wind or a thaw, and whether the stain grows gradually or appears suddenly. Recording these conditions helps choose places to inspect without unnecessary dismantling. Leave the diagnosis of causes and the scope of repair to a contractor, who should describe the defect found.

By |2026-11-14T16:31:03+01:002025-10-06|Construction basics|Comments Off on What should you do after spotting a roof leak?

Comparing two steel building quotations line by line

One offer quotes the price of the structure, the other also covers assembly and cladding. Both can be described as a steel hall with the same floor area. Without a breakdown of the scope, however, it is hard to judge which one meets the investor's needs. First the proposals must be brought to a common level. Only then does a discussion of the price difference and possible savings make sense. Begin the comparison with the dimensions and how they are stated. External and usable floor area need not be identical. The eaves height does not describe every point under the rafter. A steel hall should be shown in plan and section, with gates, columns and the required equipment. This makes it possible to spot differences that are invisible in a short description.

By |2026-11-15T03:32:27+01:002025-09-29|Construction basics|Comments Off on Comparing two steel building quotations line by line

IKO enertherm ALU TG: joints within the field and at the perimeter of the insulation

The ALU TG tongue-and-groove joint organises the connection of adjacent boards within the field. At the perimeter and around openings, cuts may occur that remove part of the factory geometry. The system should allow for such terminations. It cannot be assumed that the TG designation resolves the sealing of all cut edges. The cross-section under consideration comprises thermal insulation joined with a factory tongue and groove. The function of IKO enertherm ALU TG must be described together with the layers adjoining its surface. An important point of connection is the edge of a cut piece without a preserved factory tongue. The basis for coordination is a row plan indicating the edges remaining after cutting. Before selecting materials, the width of the last strip and the position of the joint terminations must be established so that the sequence of layers has a real reference.

By |2026-11-16T01:36:43+01:002025-09-29|Construction basics|Comments Off on IKO enertherm ALU TG: joints within the field and at the perimeter of the insulation

How do you choose the wool thickness when a building has a warm and a cool section?

Not every wall has the same job. A single building may contain a heated workshop, a cool store and a small sanitary back room. When choosing a mineral wool panel, it is worth starting with a map of these zones. The 60–200 mm range is a convenient point of comparison, but it is not a universal set of answers for every function and every system. Mark which rooms will be heated continuously and which only during visits. Also establish the temperature in adjacent zones. A wall separating a warm workshop from a cool store also transfers heat, even though it is inside the building. It cannot be treated in the same way as a partition between similarly heated rooms.

By |2026-11-14T10:16:20+01:002025-09-23|Construction basics|Comments Off on How do you choose the wool thickness when a building has a warm and a cool section?

What does a roofing underlay do and how do you choose one?

The underlay membrane beneath metal roofing is there to intercept water that gets under the covering and direct it outside before it reaches the insulation or structure. When choosing, check whether the manufacturer allows installation on the given substrate, along with water resistance, temperature range and the durability of joints. The Sd value alone does not settle suitability, because the whole roof assembly matters. Also establish how laps and the eaves termination are detailed, since these determine how the membrane performs in practice.

By |2026-11-14T23:27:23+01:002025-09-23|Construction basics|Comments Off on What does a roofing underlay do and how do you choose one?

What to look for during an autumn roof inspection

Base the autumn roof inspection on a comparison with earlier checks rather than assessing it from scratch. Document the condition of the surface, details, drainage and layers visible from the loft, recording specific defects instead of a general impression. The key decision is separating urgent securing from planned work, so note the location, description and date, and attach labelled photos. Remember events since the last inspection, such as gales or hail, which may have affected the coating, flashings or fixings. Choose conditions that allow safe inspection.

By |2026-11-14T23:26:29+01:002025-09-16|Construction basics|Comments Off on What to look for during an autumn roof inspection