About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

Five roofing defects to look for at handover

At roof acceptance, agree with the contractor which covered works—the substructure, membrane and some connections—will be checked before being concealed, and ask for photos marked by roof slope. This concrete decision helps catch errors in support, fixing, flashings, ventilation and cleanliness before they become invisible. Assess the work against the design and the specific covering's instructions, not a universal pattern. For final acceptance, prepare the material specification and detail drawings so you can discuss specific discrepancies rather than a general impression.

By |2026-11-15T03:30:31+01:002023-07-06|Construction basics|Comments Off on Five roofing defects to look for at handover

Choosing trapezoidal steel sheets for the job: roofs, façades and structural applications

Choosing a trapezoidal profile is best begun from inside the building. Will it be heated? Will wet equipment be brought in? Will anyone be working under the roof for many hours? The answers help determine the layers required. Only then do you compare profile, steel thickness, coating and order cost. On a wall, the trapezoidal sheet forms a protective skin and shapes the look of the façade. On a roof, it must work together with the drainage system and adequate support. Not every variant within one family suits both applications. When choosing, check the intended use of the specific section.

By |2026-11-14T16:28:30+01:002023-06-22|Construction basics|Comments Off on Choosing trapezoidal steel sheets for the job: roofs, façades and structural applications

The parts of a roof structure and what each one does

How a roof performs depends above all on the complete load-bearing structure, not on the covering alone. It is worth checking that every element has a clearly defined role and that loads have a continuous path to the walls or frames. In a house, a timber truss may include rafters, collars, purlins and supports, while a hall may use steel members with covering on purlins. Pay attention to details: the wall plate and its anchorage, and flashings at the eaves, ridge, valley and chimney. When comparing offers, ask for a layer cross-section and drawings of the connections.

By |2026-11-14T23:26:51+01:002023-06-22|Construction basics|Comments Off on The parts of a roof structure and what each one does

How do you flash a chimney on a trapezoidal steel sheet roof so that it drains water?

Good chimney flashing leads water past the obstruction and back onto the roof. Sealant is only part of the solution. The back of the chimney and the junction between the metal sheet and its wall require the most attention. The detail must also allow for movement of the roof. The sequence below helps you understand the work and check the scope of the order for the roofer. You need the chimney dimensions, the roof pitch and the exact trapezoidal sheet profile. The position of the chimney relative to the ridge and the roof valleys is also important. The more water flows in from the higher part of the roof, the more important it is to divide it effectively. The detail is not selected on the basis of the covering colour alone.

By |2026-11-14T10:12:40+01:002023-06-14|Construction basics|Comments Off on How do you flash a chimney on a trapezoidal steel sheet roof so that it drains water?

Choosing gutters for a metal roof by runoff and roof geometry

The answer is that choosing gutters for a metal roof starts with dividing the roof into catchment areas, not with picking a material. Check how much water will reach each gutter run, taking into account eaves length, valley positions and height differences. Then compare steel and PVC as complete systems, including outlets and downpipes, using the manufacturer's rules for the specific layout. Also examine the eaves detail, downpipe placement and the water path at ground level. Only then assess the profile shape and the completeness of the component list.

By |2026-11-14T23:26:08+01:002023-06-07|Construction basics|Comments Off on Choosing gutters for a metal roof by runoff and roof geometry

What belongs in a complete roof estimate?

A complete roof is not just the covering but a whole system of structure, insulation and details whose scope must be settled before comparing offers. Check whether the quote includes the layers beneath the metal sheet, fixings, flashings and drainage, and who is responsible for the junctions between them. A sandwich panel may replace several elements, but it does not remove the need to design supports and seals. At handover, assess the system in stages before subsequent layers conceal the previous ones.

By |2026-11-14T23:26:35+01:002023-05-29|Construction basics|Comments Off on What belongs in a complete roof estimate?

PIR or XPS for a flat roof: what does the position of the insulation tell you?

PIR and XPS are not chosen for a flat roof on the basis of lambda alone. First you need to know where the insulation will sit relative to the water-retaining layer. A dry board under a membrane performs differently from a material above the waterproofing, under gravel or a terrace. The requirements, details and the point of comparing prices all depend on this arrangement. In a traditional roof the thermal insulation is usually below the waterproof layer. In an inverted roof the order is different: the insulation goes above the waterproofing and may come into contact with water. This distinction matters more than the flat shape of the roof as seen from the street.

By |2026-11-14T10:17:33+01:002023-05-25|Construction basics|Comments Off on PIR or XPS for a flat roof: what does the position of the insulation tell you?

How to insulate a room from the inside with aluminium-faced PIR board?

Internal insulation can improve comfort where a wall is cold, but joints need careful planning. In a small room every centimetre counts, and after renovation it is difficult to return to a covered wall. The aluminium facing is part of the protection against vapour penetration. Its performance depends on the airtightness of the entire surface, including at the ceiling and window. Before choosing the board, check that the wall is dry and that water is not getting into it. Stains at the windowsill may result from an external leak. Dampness at the floor may have a different cause. Covering both places with insulation will hide the symptoms but will not stop moisture ingress.

By |2026-11-14T10:16:39+01:002023-05-22|Construction basics|Comments Off on How to insulate a room from the inside with aluminium-faced PIR board?

How do you calculate the screws for the panels when the design specifies fixings at the supports?

The question of the number of screws per metre of panel is too general to prepare a safe fixing. First you need to know where the supports are and what forces act on the cladding. Only from the designed layout does the quantity to order emerge. Converting it to a square metre may help with the budget, but it does not replace the selection. A linear metre of edge, a square metre of wall and a metre of panel length are different units. Screws for flashings may be counted along their edge. The main panel fasteners result from the points where the elements cross the supports and from the required fixing layout. Combining these data into a single number leads to errors.

By |2026-11-14T12:36:59+01:002023-05-17|Construction basics|Comments Off on How do you calculate the screws for the panels when the design specifies fixings at the supports?

Choosing battens and supports for trapezoidal steel roofing

There is no single universal batten spacing for trapezoidal sheet – the choice depends on the specific profile, sheet thickness, support scheme and loads. Readers should therefore check whether the load table matches the actual roof, not just the T18 or T35 label. This guide explains what data are needed, how to read the table, and when a timber frame or steel purlins will do their job. It also covers laps, edges and preparing an order, so that solutions are not copied from tile-effect sheeting.

By |2026-11-14T23:27:18+01:002023-05-13|Construction basics|Comments Off on Choosing battens and supports for trapezoidal steel roofing