Building basics2026-11-15T18:16:21+01:00

Choose a product group

Metal roofing

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Building basics

Sandwich-panel.pl explains the basics of choosing sandwich panels, PIR insulation boards and metal roofing. Learn how the core differs from the facings, what the thickness describes and how the sheet dimensions relate to the effective cover area. The guides are intended for people planning a garage, industrial building, workshop or farm building. They explain which details to collect before ordering, how to identify accessories and what to inspect when the goods arrive. Use the articles to compare materials and prepare the questions that need to be resolved for your project.

How can snow be removed without damaging the roof covering?

Before you start clearing snow, establish a plan that considers the roof's load-bearing capacity, its shape and people's safety. The layer's thickness does not reflect the actual load – wet snow and ice are far heavier than powder. Carry out the work with proper access and protection, and do not chip ice off metal coverings. What matters is the weight of the snow lying there, how unevenly it is distributed and the condition of the structure. Drifts near higher parts of the building load the roof differently from an even layer. Do not assume one centimetre figure is safe for every building. Visible deformation, unusual cracking or faults in building elements require prompt assessment by a specialist.

Metal pickets in fence bays of different widths: arranging the gaps

Bays in an existing fence rarely have perfectly equal clear widths. Differences also arise at new driveways, corners and gates. Metal fence pickets can be laid out so as to maintain a calm rhythm. However, it is not enough to divide the entire fence length by the width of one element. Each bay has its own edge gaps. It is worth calculating them before purchase, rather than correcting the last section during installation. First, establish between which points the pickets will be distributed. The clear width between the posts is not always equal to the width available for the infill. Part of the space may be taken up by a frame, a trim strip or another element of the system. The measurement should correspond to the actual method of installation. Record dimensions in a single unit, preferably in millimetres.

Coordinating a photovoltaic roof with rooflights and ventilation equipment

Skylights and fans do not rule out a photovoltaic roof, but they require a shared plan. Every opening takes up space, can cast a shadow and creates an area requiring a weathertight connection. In a steel BIPV system, the active fields can be supplemented with passive covering. This means the technical parts of the roof do not have to disrupt its rhythm. The best result is achieved when the layout of the equipment is known before the panels are ordered. The ventilation, daylighting and photovoltaic designs may all relate to the same roof surface. If each contractor chooses a location independently, clashes arise. A unit may end up above a cable route or in the middle of the best active field. Moving it after the covering has been ordered can be costly and disrupts the geometry of the roof slope.

What are the benefits and challenges of a mansard roof?

A mansard roof can be beneficial when the steep lower section of the slope genuinely improves the attic's function, not just the façade's appearance. Check the heights at specific points on the section, because the structural layout may introduce supports that restrict the arrangement. Assess the option on a completed layer section, accounting for insulation and lining, which take up space. A mansard is not automatically a cheaper way to gain an extra storey – its cost-effectiveness depends on the interior's needs and the feasibility of the details.

Choosing tile-effect metal roofing for a traditionally styled home

For a house in a traditional style, a metal roof tile with a gentle, wavy pattern usually fits better than a strongly geometric profile. Before choosing a pattern, however, check how the covering will look against the whole building form, its wall colour and the size of the roof slopes. Assess the sample in a photograph of the house, not just on a counter. At the same time, verify the roof pitch, the condition of the structure and how the eaves and ridge are made. Traditional architecture does not impose a single roof pattern, so it is worth matching the rhythm of the pressings to the building's dominant lines.

BauderPIR T under the covering: how the slope of the entire roof is created

BauderPIR T has no factory-applied facing, so its surface must not be equated with the foil on an aluminium-faced board. The method of constructing the covering must follow from the correct roof solution. At the same time, the tapered boards are responsible for the geometry, and the covering for watertightness. These functions must be checked separately and combined in a single cross-section. The cross-section under consideration covers a roof with unfaced tapered insulation boards. The role of BauderPIR T must be described together with the layers adjoining its surface. An important junction point is the roof valley conducting water towards the outlet. The basis for agreement is the slope drawing with the direction in which the thickness increases. Before selecting materials, the levels of the substrate and the course of the water-collecting lines must be established so that the sequence of layers has a real reference.