About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

Mineral wool wall panels: how to read the U-value and thermal conductivity

Various heat-related figures appear on the material label and in the panel datasheet. Lambda describes conduction within the material, while U helps assess transmission through a building element or product in a specific configuration. These values are not interchangeable. Distinguishing between them makes it easier to select the wall of a workshop where people will be working throughout the day. The thermal conductivity coefficient is written as lambda and given in W/(m·K). At the same thickness, a lower value means greater thermal resistance of a homogeneous layer. However, the value appropriate to the specific core and the adopted calculation method must be used. A figure from any mineral wool mat should not be taken to calculate a sandwich panel.

By |2026-11-14T10:15:56+01:002024-04-26|Construction basics|Comments Off on Mineral wool wall panels: how to read the U-value and thermal conductivity

Snow stops or snow fences? Choosing snow retention for a roof

The choice between snow guards and snow fences depends mainly on the role the protection is to play on a given roof slope. It is worth checking the roof length and pitch, local snow conditions and areas requiring protection, such as entrances or walkways. Equally important is matching the fixings to the covering and structure. The article explains how small point elements differ from continuous barriers and why their layout should follow a technical solution rather than chance.

By |2026-11-14T23:26:14+01:002024-04-23|Construction basics|Comments Off on Snow stops or snow fences? Choosing snow retention for a roof

Where can you use T14 steel sheet, and how should it be supported?

T14 trapezoidal steel sheet can serve as a lightweight covering or cladding. However, its suitability is not determined by the name alone. The profile shape, steel thickness, supports and load are what matter. A sheet over an open shelter is selected differently from one on a workshop wall. Start with the building's function. Only then compare dimensions and price. The letter T indicates the family of sheets with a trapezoidal cross-section. The number refers to the nominal profile height. It does not describe the thickness of the steel core. A T14 sheet is therefore not a sheet 14 mm thick. It is a thin sheet stiffened by ribs.

By |2026-11-14T10:12:37+01:002024-04-23|Construction basics|Comments Off on Where can you use T14 steel sheet, and how should it be supported?

What do purlins do in a roof or steel-framed building?

Purlins are structural members that support other parts of a roof or its covering directly – in a house they work with rafters, while in a hall they work with trapezoidal sheet or sandwich panels. When choosing, it is worth checking not only the covering profile but above all the spacing and width of supports, the span arrangement and the required loads, as these determine the section selection. A higher sheet profile alone does not allow supports to be spaced arbitrarily. The supplier also needs the layer build-up and fixing method, and the documentation should state who is responsible for the calculations and section selection.

By |2026-11-14T19:44:43+01:002024-04-08|Construction basics|Comments Off on What do purlins do in a roof or steel-framed building?

Choosing a timber roof structure and organising the carpentry work

Choose the truss type only after establishing the roof geometry and the points that can carry loads — these, not the amount of timber, determine the arrangement. Check that the planned covering, together with battens, insulation and finish, is included in the design, and whether attic needs require a post in an unsuitable place. Compare the completed structure on the same assumptions, including connections and assembly. Leave the assessment of the scheme to the designer, who will match the arrangement to the actual support conditions.

By |2026-11-15T03:30:35+01:002024-04-07|Construction basics|Comments Off on Choosing a timber roof structure and organising the carpentry work

Reading roof pitch in degrees and as a percentage

The key is to establish whether the manufacturer states the minimum in degrees or as a percentage — the two are not interchangeable. The building owner and the trade should therefore check the unit in the instructions and the conditions under which it applies, then compare these with the actual roof pitch. Account must also be taken of the horizontal projection rather than the slope length, possible installation tolerances and places where water may collect. Only on this basis can it be judged whether a given roofing system is suitable or whether the design needs to change.

By |2026-11-14T23:26:31+01:002024-04-03|Construction basics|Comments Off on Reading roof pitch in degrees and as a percentage

Mineral wool or PIR: which core suits the way the building is used?

The choice between mineral wool and PIR should not begin with the question of which material is always better. What matters more is the specific task of a given wall or roof. A warm workshop, a noisy workshop and a cool storage area each need a different set of characteristics. A comparison makes sense when it covers complete panels, the same function and clearly stated requirements. A mineral wool panel has a fibrous core, while PIR has a closed-cell foam core. In both cases, the facings and joints also determine performance. Comparing the insulation materials alone is not enough. Two panels with the same core can differ in load-bearing capacity, weight and range of application.

By |2026-11-14T12:34:26+01:002024-04-03|Construction basics|Comments Off on Mineral wool or PIR: which core suits the way the building is used?

Matching the flashing finish to the facing of a sandwich panel

Well-matched flashings fit sandwich panels in dimension, application and surface type. The same colour alone is not enough to assess the whole set. Barge boards, ridge caps or gutter aprons may come from sheet with a different finish than the panel cladding. It is worth establishing the specification before ordering. This helps limit visual differences and check whether the material suits the building's conditions of use. Steel sheet forms the substrate of the flashing. A metallic coating protects this substrate against corrosion, and in colour-coated sheet an appropriate system of organic layers is added on top. That is why the terms galvanised and coated do not have to describe two entirely separate groups. Colour-coated sheet may have a zinc layer beneath the paint.

By |2026-11-15T03:33:05+01:002024-03-24|Construction basics|Comments Off on Matching the flashing finish to the facing of a sandwich panel

Planning drainage for an integrated photovoltaic roof

An energy-generating roof must still drain water efficiently. The cells do not change the fundamental importance of the slope, flashings and gutters. In an integrated steel system, the entire roof slope should be designed as a single assembly comprising both active and passive elements. This makes it easier to organise the surface. However, it requires careful detailing at the eaves, ridge, valleys and every point where water changes direction of flow. Water flows down the roof according to its geometry, regardless of the arrangement of the cells. It must pass safely through the joints and reach the gutters or other designated outlets. It cannot be assumed that the active field alone ensures the watertightness of the entire roof slope.

By |2026-11-15T18:27:53+01:002024-03-22|Construction basics|Comments Off on Planning drainage for an integrated photovoltaic roof

How to order tile-effect metal roofing cut to size without mistakes in length and quantity?

Ordering tile-effect metal roofing cut to size starts with measuring the finished roof geometry. A project drawing helps, but it does not always reflect all dimensions of the completed structure. The profile must also be chosen, because its rhythm affects the lengths and the division of the sheets. A good material schedule describes each roof slope separately. It is best to measure the structure in a state that allows the edges of the covering to be determined unambiguously. The positions of the eaves, ridge and flashings must be known. A measurement taken before these details are established is only preliminary. A change in the sheet overhang can affect the length of the entire order.

By |2026-11-14T10:15:21+01:002024-03-17|Construction basics|Comments Off on How to order tile-effect metal roofing cut to size without mistakes in length and quantity?