What do roof battens and counter-battens do?

Purlins and counter-purlins serve distinct functions, so when choosing the batten layout it is best to start from the roofing system's requirements rather than from ready-made spacings. Purlins support the sheeting and mark the fixing points, while counter-purlins create a ventilation gap above the underlay. The building owner and the trade should check the layer build-up, the route for moisture drainage and the load-bearing capacity of the supports. Note that dimensions and spacings are not universal – even similar profiles may need a different arrangement. Leave the detailed design decisions to the designer.

By |2026-11-14T23:27:20+01:002022-09-03|Construction basics|Comments Off on What do roof battens and counter-battens do?

How are rafter dimensions and spacing determined?

Choosing rafter size and spacing relies on calculations for the particular building. Span, support method, timber class and loads from the covering, snow and wind all matter. For a metal roof, there is no single safe spacing that works everywhere. A lighter covering does not let you reduce structural sections on your own. The designer needs the roof geometry, support layout and all layers. The length of the unsupported run is key. Two roofs of the same width may have a different structural system. An extra purlin changes how the structure performs, and removing it can worsen conditions. Consider the site location and weather exposure.

By |2026-11-14T19:54:04+01:002022-08-25|Construction basics|Comments Off on How are rafter dimensions and spacing determined?

How to choose a covering for a mansard roof

The covering for a mansard roof must be selected separately for the lower and upper slopes and for their junction, as each zone has different fixing and flashing requirements. Before choosing a material, check the actual angles and lengths of both sections, as well as the presence of dormers, chimneys and windows, which complicate sheet layout. The slope break is crucial: water from the upper part must drain safely onto the lower without backing up under the covering. Base the assessment on an accurate plan and sections, not on the roof name alone.

By |2026-11-14T16:31:31+01:002022-08-25|Construction basics|Comments Off on How to choose a covering for a mansard roof

How much steel sheet is needed for a 100 m² roof and how do you calculate the order cost?

A price enquiry for ‘100 metres of steel sheet’ needs clarification. One hundred square metres of roof surface is not the same as one hundred linear metres of sheet. The quote also requires the cover width, the lengths and the billing method. The example below shows the calculation for a simple roof with an actual area of 100 m². A square metre describes an area. A linear metre means the length of material at a specified width. If a sheet covers 1.10 m, then 100 linear metres corresponds theoretically to 110 m² of coverage. This does not yet indicate how that length is to be divided between roof slopes and overlaps.

By |2026-11-14T12:36:51+01:002022-08-08|Construction basics|Comments Off on How much steel sheet is needed for a 100 m² roof and how do you calculate the order cost?

Inspecting flashings on a steel building when several trades share the work

Roofs and walls made of sandwich panels are often erected in parallel with the installation of gutters, doors and services. Flashings connect the scope of these works. It is easy then to overlook a small element or to cover a joint before inspection. A well-planned handover covers successive stages, not just the finished façade. It allows checking what will no longer be visible once the works are complete. It is worth starting the review from the lower part of the walls. Starter profiles and plinth flashings are checked before subsequent layers are closed. The next groups cover corners, openings, eaves and the ridge. Such an order is clearer than a single list of elements without their location.

By |2026-11-15T03:33:24+01:002022-07-23|Construction basics|Comments Off on Inspecting flashings on a steel building when several trades share the work

Which flashings does a roof need?

The set of flashings is determined by the roof geometry, not by colour alone. Begin with a cross-section drawing that shows where the metal ends and how water drains away. Check how the eaves, side edges, ridge, valley and junctions at the chimney and wall are resolved. For each detail, support, laps and compatibility with the covering matter. Names are often used imprecisely, so base the order on dimensions and function rather than on the element's name alone.

By |2026-11-14T23:28:06+01:002022-07-17|Construction basics|Comments Off on Which flashings does a roof need?

What affects the environmental impact of metal roofing?

A metal roof can be an environmentally friendly choice, but only when the comparison covers a complete roof with comparable insulation and service life, not just a sheet of steel. It is worth checking whether the environmental declaration refers to a specific product, which life-cycle stages it covers and whether its unit matches the actual covering area. The cutting plan and the expected dismantling also affect the final balance. Rather than general assurances, the decision should rest on documents and service assumptions.

By |2026-11-14T16:31:05+01:002022-07-13|Construction basics|Comments Off on What affects the environmental impact of metal roofing?

How can you recognise a well-prepared supplier of panels and sheets?

Warehouse size tells you little about how smoothly an order will go. A supplier should be able to identify the material, confirm the batch and say exactly what the delivery includes. Ask the same questions of a small depot as you would of a large distribution centre. For sandwich panels, look for the intended use, core, thickness, facings, coating and cover width. For trapezoidal steel sheet, check the profile, actual steel thickness, cover width and which face is intended to be exposed. Labels such as “insulated” or “for roofs” are too vague to check against the drawings.

By |2026-11-14T12:35:55+01:002022-06-24|Construction basics|Comments Off on How can you recognise a well-prepared supplier of panels and sheets?

How to choose trapezoidal steel sheet for a workshop roof? Profile, thickness, fleece and full cost

The roof over a workshop is there to protect equipment and allow comfortable use of the interior. Cheap sheet metal alone does not solve the issues of moisture, heating or noise. It is therefore worth starting the choice of trapezoidal steel sheet with what will happen beneath it. Only then are the profile, steel, coating and accessories selected. A tool store opened once a week has different needs from a workshop used daily. Temperature, humidity and the presence of people matter. If wet items are dried inside, provision must be made for removing moisture. Sealing all openings tightly is not a way to make it disappear.

By |2026-11-14T12:35:33+01:002022-06-07|Construction basics|Comments Off on How to choose trapezoidal steel sheet for a workshop roof? Profile, thickness, fleece and full cost

How to install modular tile-effect metal roofing

The key to correct installation of modular metal roof tiles is confirming that the roof pitch and layers meet the requirements of the chosen profile, and that the batten grid is level and follows the instructions. Check the eaves line, diagonals and support plane, as well as the completeness of material, flashings and accessories. Batten spacing follows from the profile module, and the first row sets the run of the entire covering. The order of laying depends on the edge shape and water drainage. Before final fixing, assess the fit of components and the row line.

By |2026-11-14T19:47:48+01:002022-06-03|Construction basics|Comments Off on How to install modular tile-effect metal roofing