α-therm SARKING: choosing roof layers with IDELCO insulation

IDELCO α-therm SARKING is used to insulate pitched roofs above the rafters. The PIR board has a multi-layer aluminium laminate on both sides and a tongue-and-groove profile on all four edges. However, it does not include a factory-applied membrane with laps: the underlay is selected separately. The roof cross-section must combine continuity of the thermal insulation with support, fixing of the counter-battens and drainage at the eaves. Laying it over the timber reduces gaps in the primary insulation layer, but does not eliminate all thermal bridges. In this article we discuss junctions with the wall, flashings and openings, as well as the effect of the new layers on the height of the roof slope. The name “polyurethane insulation” does not describe these installation solutions.

2026-11-16T06:03:48+01:00

What frame should be prepared for walls made of panels with a mineral wool core?

A level façade starts with a properly prepared frame. A panel with a mineral wool core transfers loads through a specific arrangement of supports, but it does not correct a crooked structure. In a small workshop, doors, windows and equipment fixing points also matter. Planning these before installation avoids later cutting and adding random profiles. Loads acting on the panel are transferred through fasteners to rails or columns, and then to the main structure and foundations. Every connection along this path must be checked. A suitably thick panel alone does not solve the problem of a weak rail. It also does not replace bracing unless it has been designed for that function.

2026-11-14T10:15:59+01:00

Choosing wall panel fixings to suit the supporting structure

The fastener for an insulated wall panel with a mineral wool core must hold the cladding and not damage its facings. Its length is only one of the pieces of information required. The type and thickness of the support, the wind load and the way forces are transferred through the joint also matter. Selection starts with the construction and ends with checking that the washer is correctly pressed. A thin steel purlin, a thicker profile and a reinforced concrete support require different solutions. In steel, the drill-through capability and the correct thread engagement are important. For concrete, suitably selected anchors and a suitable method of preparing the hole are used. A solution cannot be transferred between substrates solely because the screw has a matching length.

2026-11-14T10:15:57+01:00

How does roof pitch affect the choice of insulated roof panels?

The term “flat roof” is sometimes used for several different solutions. A roof made of sandwich panels with a low pitch must still drain water across the profiled surface and the joints. It does not thereby become a flat roof with a continuous membrane. The permissible pitch is determined by the specific panel, the method of jointing and the geometry of the finished roof slope. In a panel roof, the outer steel skin together with the joints forms the covering. In another arrangement, the structure supports the insulation and a separate waterproof layer, for example a membrane. Both roofs may look almost flat from the street, but they handle drainage and weathertightness differently.

2026-11-14T16:27:43+01:00

What to consider when planning a hipped roof structure

The key decision for a hipped roof is to agree the support layout with the attic needs early, before the truss design is produced. It is worth checking where the structure can safely transfer loads to walls, columns and the floor, and how room arrangement will affect the possible schemes. Corners and shorter rafters collect forces from a larger area, so their sections require calculation rather than copying from a gable roof. The planned covering material, openings and services must also be considered at this stage.

2026-11-14T23:26:53+01:00

Can EPS insulation be used in a green roof?

EPS can be part of a green roof if the selected grade suits its construction and loads. In a traditional build-up it sits beneath the waterproofing. Plants, substrate and drainage form further layers with their own requirements. The weight when saturated, root protection and access to the drainage must be checked. In a traditional build-up EPS lies below the watertight covering. Above the waterproofing are the layers needed for protection, drainage and water retention, and for plant growth. This sequence allows suitable roof insulation to be used, shielded from precipitation. However, this does not mean that any façade EPS is suitable beneath a roof garden.

2026-11-16T06:08:30+01:00

What can a 60 mm mineral wool wall panel be used for, and what about the 40 mm version?

A thin mineral wool panel may be considered where a slim-profile cladding is important. However, good thermal performance or a specific fire resistance should not be assumed in advance. A range starting from 60 mm in one system does not mean that all panels on the market begin at the same point. The 40 mm version must be checked separately. A partition between two rooms at a similar temperature performs differently from a workshop wall facing the yard. In the first case, the temperature difference may be small. In the second, heat loss, the internal surface temperature and the requirements of the whole building must be assessed. The nominal thickness does not explain these differences.

2026-11-14T10:16:17+01:00

Metal picket fencing for a seasonal home: making upkeep easier

At a house visited seasonally, it is worth limiting the work that has to be repeated after every arrival. Metal fence pickets with a factory coating do not require the same care as untreated wood. This does not mean, however, that they can be completely forgotten. The choice of material should take into account the surroundings, access for cleaning and the length of absences. The most convenient fence is one whose condition can be quickly assessed and maintained without complicated procedures. A seasonal house can stand in very different conditions. An open plot, a damp environment and proximity to sources of contamination are not the same environment. Coatings have specific limitations of use. Under special conditions, for example elevated salinity, confirmation of the suitability of the chosen material must be obtained. A general declaration of weather resistance is not enough.

2026-11-15T18:27:07+01:00

What does non-combustible core mean in a wall panel with mineral wool?

Mineral wool can form the non-combustible core of an insulated wall panel with a mineral wool core. However, this does not mean that all components of the complete product receive the same class as the insulation material itself. When selecting a wall, a distinction must be made between reaction to fire and fire resistance. Each of these pieces of information answers a different question regarding the behaviour of the building element. In addition to the wool, the panel contains steel facings, bonding layers and coatings. The joint may include additional seals. When assessing the product, these parts cannot be omitted and the class of the core material cannot be transferred to the whole. This is a similar error to determining the load-bearing capacity of a wall solely on the basis of the sheet thickness.

2026-11-14T10:16:31+01:00

How much does a house with sandwich panels cost when the full scope is priced?

The price of the panels is not the price of a house ready to move into. The shell is joined by the structure, foundations, services and finishing, as well as solutions ensuring comfort. A sensible budget starts from one scope of works. The example below shows the method of calculation using contractual amounts; it is neither a market price list nor a sales offer. One quote may cover only the frame and panels. A second will add windows and doors, and a third services and floors. These sums do not describe the same result. Before comparing, note what is to function on the day of handover and what works will remain on the investor's side.

2026-11-14T12:37:20+01:00