About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

How to prepare for the installation of trapezoidal steel sheets

The key decision when installing trapezoidal sheet is to tie the choice of panels to the actual roof conditions, not to the profile symbol alone. It is worth checking dimensions, pitch, support spacing and the building's purpose, since a shelter, garage and hall roof may need different layer build-ups. The documentation should specify loads and fixing, while the product data sheet covers geometry and the roof variant. Establishing these facts before cutting limits improvisation and shows whether the proposed solution suits that particular roof.

By |2026-11-14T23:27:42+01:002022-01-24|Construction basics|Comments Off on How to prepare for the installation of trapezoidal steel sheets

Can every roofing membrane be in direct contact with EPS?

The roof membrane and EPS must be compatible as components of a single system. Some coverings require separation from polystyrene by a suitable layer. Others can work in direct contact in specific solutions. The choice is determined by the documentation for the specific membrane, as well as the method of fixing, the substrate and the fire requirements of the roof. Roof membranes are made from various plastics and have different compositions. There are also variants with a factory backing, reinforcement or additional layers. A similar colour and thickness do not prove the same compatibility with EPS. The exact product type must be checked. A general name for a material group does not replace the conditions of use for a specific variant. In some coverings, the problem is the contact of the membrane's components with the adjacent material.

By |2026-11-16T06:08:15+01:002022-01-24|Construction basics|Comments Off on Can every roofing membrane be in direct contact with EPS?

How to plan a garage made from insulated panels and calculate its cost?

A garage can be used solely for parking or become a small workshop. These two ways of using it require different decisions about insulation, the door and ventilation. The construction cost is therefore worth calculating from the interior plan. The price of the panels alone does not show how much a finished, dry and convenient place for the car and tools will cost. Mark the outline of the car, the door swing and the route to the shelving. Add space for tyres, bicycles and a worktop. A wide door will not provide convenience if a column or a deep cupboard blocks the passage. The room height must take into account the door guides, lighting and any suspended equipment.

By |2026-11-14T12:34:21+01:002022-01-24|Construction basics|Comments Off on How to plan a garage made from insulated panels and calculate its cost?

Utherm Roof LE and the layers of a flat roof: selecting a complete system

The Utherm Roof LE board with aluminium laminate requires a compatible set of roof layers. Its thermal parameters alone do not determine the adhesion of the adhesive or the way forces are transferred. The right system combines the advantages of thin insulation with carefully designed connections. Utherm Roof LE is a PIR board intended for flat roofs and roofs with a low pitch. The core is covered on both sides by a multi-layer, gas-tight laminate. The terms “polyurethane boards” and “polyurethane foam” are broader than the precise designation of the PIR product. PIR boards must be placed in a section that explains the limited insulation height at the roof parapet with Utherm Roof LE. When selecting the layers, the thickness of Roof LE, the slope and the other roof layers must be added together.

By |2026-11-16T01:37:01+01:002022-01-22|Construction basics|Comments Off on Utherm Roof LE and the layers of a flat roof: selecting a complete system

How to choose the right membrane for each roof layer

Roofing membrane should be chosen primarily by the function it is to perform at a specific point in the building envelope, not by its trade name. Before buying, mark on the roof section where the material will be laid: under metal sheeting it may be an underlay, while on the warm side it usually controls water-vapour ingress and helps maintain airtightness. On a flat roof, membrane may mean the final waterproofing. Include a description of the structure, covering and substrate, plus how the interior will be used, in your enquiry.

By |2026-11-14T19:46:39+01:002022-01-22|Construction basics|Comments Off on How to choose the right membrane for each roof layer

How should you plan thin internal insulation for a wall on a plot boundary?

For a wall standing on a plot boundary, adding insulation on the outside may be difficult. This is where the idea of internal insulation comes in. A thin PIR board can be helpful in a small interior, but the space saving must be weighed against the condition of the wall, the routing of services and the possibility of sealing the new layer tightly to the ceiling. The building's position must be confirmed on the basis of documents and the actual condition. The solution cannot rely on the assumption that a few centimetres beyond the boundary do not matter. Any agreements, access from the neighbour and requirements for the wall must be clarified before the detailed design.

By |2026-11-14T10:16:56+01:002022-01-22|Construction basics|Comments Off on How should you plan thin internal insulation for a wall on a plot boundary?

Choosing a soffit and estimating the cost of finishing the eaves

The choice of soffit is determined primarily by the roof eaves ventilation method and its construction, not by the appearance of the panels alone. It is therefore worth first establishing which solution is permitted for the given eaves, and only then comparing materials and layouts. Check whether the chosen variant ensures airflow, access for cleaning, and a consistent finish at the wall and gutter. When costing, do not stop at the price per square metre – compare the scope of the support frame, accessories and labour, as this determines the real cost.

By |2026-11-14T23:28:50+01:002022-01-19|Construction basics|Comments Off on Choosing a soffit and estimating the cost of finishing the eaves

Four checks before you choose tile-effect metal roofing

Before choosing tile-effect metal sheets, check the requirements for the particular model against the shape of the roof and the condition of its supporting layers. Each system has its own permitted range of pitches. Where the manufacturer requires an additional layer beneath the covering, the design must specify its construction. On a renovation, check that the roof timbers are dry and sound. Record the sheet specification and coating together with a drawing of the sheet layout. The roofer can then identify the flashings, fixings and cuts the job will need.

By |2026-11-14T19:54:48+01:002022-01-15|Construction basics|Comments Off on Four checks before you choose tile-effect metal roofing

termPIR AL GK in the attic: joining wall and roof insulation

In an attic, the wall, the sloped ceiling and the ceiling form a single enclosing envelope for the room. termPIR AL GK must be joined to the remaining insulation so that no cold gap occurs. Evenly covering only the flat part of the wall does not fulfil this task. termPIR AL GK is a composite. The insulation core made of PIR foam has a gas-tight facing on both sides, and on the room side there is a 12.5 mm thick plasterboard. When selecting PIR boards for the assembly, draw the wall from the room side, where a single board is to provide both insulation and the substrate for the finish in the actual cross-section. The masonry behind termPIR AL GK must be surveyed before it is sealed under the insulation and the new plasterboard surface, because the remaining layers must match the same solution.

By |2026-11-16T01:35:09+01:002022-01-08|Construction basics|Comments Off on termPIR AL GK in the attic: joining wall and roof insulation

Trapezoidal steel sheet or tile-effect metal roofing for a house? Choosing by roof slope and residents’ needs

Trapezoidal steel sheet can look good on a house, and tile-effect metal roofing is not reserved for a single building form. The choice is determined by the covering pattern, the pitch and the number of details. Residents' comfort also depends on the layers beneath the metal sheet. Instead of looking for the material best suited to every house, compare two complete solutions for your own roof. Trapezoidal sheet creates straight lines running along the roof slope. It emphasises economical geometry well. Tile-effect metal roofing introduces an additional transverse rhythm. It can have gentle waves or flatter fields. Both solutions are available in various colours and coating textures.

By |2026-11-14T10:15:04+01:002022-01-04|Construction basics|Comments Off on Trapezoidal steel sheet or tile-effect metal roofing for a house? Choosing by roof slope and residents’ needs