About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

Which documents are needed before building a house or industrial hall in Poland?

First, check whether your plot lies within an area covered by a local spatial development plan – this determines the procedure. The plan sets land use, building height, roof geometry and sometimes roof colour. If no plan exists, establish whether a zoning decision is required. Choose a design for the specific plot, considering road access, utilities and boundaries. Selecting sheet metal or sandwich panels does not settle whether notification alone suffices. Complete documentation makes costing, material ordering and deliveries easier. Decide how to proceed with your designer and the competent architectural and construction administration authority.

By |2026-11-14T19:46:41+01:002022-01-04|Construction basics|Comments Off on Which documents are needed before building a house or industrial hall in Poland?

Clay tiles or tile-effect steel roofing: what changes the cost of owning the roof?

Both coverings can serve well for years. They differ, however, in weight, method of laying and repair. The choice should be linked to the house and the planned use of the attic. The price of a single square metre of material will not show these differences. A fair comparison covers the structure, the full covering and the layers beneath it. First establish the requirements for the whole roof. Above a bedroom, thermal insulation, noise reduction and air tightness will be important. Above an unheated loft, the layer build-up may be different. The choice of metal sheet or clay tiles alone will not ensure comfort in the room beneath the roof slope.

By |2026-11-14T10:12:42+01:002022-01-02|Construction basics|Comments Off on Clay tiles or tile-effect steel roofing: what changes the cost of owning the roof?

Storing straw under corrugated fibre cement roofing: moisture and safety

Straw needs protection from water and from conditions that encourage it to become damp again. Corrugated fibre cement sheets can shelter such a store, but the covering alone does not ensure correct storage. Asbestos-free fibre cement must be selected together with ventilation, drainage and rules for using the storage area. Rain can get under an open shelter from the side, and moisture can also rise from the ground. Before choosing the sheets, the whole storage zone must therefore be assessed. The slope of the ground, the height of the stack and shelter from the prevailing direction of driving rain all matter. A roof will not fix a wet base to the stack. The arrangement of the beams should allow inspection and maintenance of the drainage. Filling the space right up to the eaves can make a leak harder to spot.

By |2026-11-15T18:28:55+01:002021-11-27|Construction basics|Comments Off on Storing straw under corrugated fibre cement roofing: moisture and safety

Choosing EPS beneath a terrace above a heated room

A terrace above a heated room is at the same time a roof and a usable surface. EPS can reduce heat losses, but it must match the waterproofing build-up and the loads from the surfacing. With boards on pedestals, local contact pressures matter. With heavy layers, creep also matters. Selection begins with the cross-section of the entire terrace. In a traditional terrace, the water-protection layer is located above the thermal insulation. EPS works beneath a covering that is to protect it from rainwater. In such a build-up, suitable roof-and-floor boards can be considered. Their suitability depends on the documentation for the solution, the loads and how the other layers are executed. The name terrace does not mean one single, always identical cross-section.

By |2026-11-16T06:08:28+01:002021-11-26|Construction basics|Comments Off on Choosing EPS beneath a terrace above a heated room

Fibre cement roofing for poultry housing: protecting the flock starts with design

The roof of a henhouse is meant to protect the interior and to work together with the systems responsible for the housing conditions. Corrugated fibre cement sheets can be included in such a design, but they will not replace ventilation or insulation. Asbestos-free fibre cement must be selected to suit the type of building, its operating temperature and the method of cleaning. Before choosing the covering, the intended use must be established. A heated building requires a different building envelope from a simple seasonal shelter. Ventilation equipment, the amount of moisture and the frequency of washing all matter. Without this information it is difficult to compare two roof systems in a useful way. It is worth separating the role of the external covering from the role of the ceiling and the layers beneath it. The roof can shield against rain, while the insulation and the airtight internal layer are responsible for limiting heat loss.

By |2026-11-15T18:28:36+01:002021-11-11|Construction basics|Comments Off on Fibre cement roofing for poultry housing: protecting the flock starts with design

Corrugated fibre cement roofing for stables: horse comfort and building maintenance

In a stable, a good roof should protect the interior, not hinder ventilation and be safe to maintain. Corrugated fibre cement sheets meet these needs if they are part of a well-considered design. Asbestos-free fibre cement is worth considering for both new builds and renovations, taking into account the condition of the structure. A stable may include loose boxes, a corridor, a tack room and a feed store. Not all rooms operate at the same temperature and humidity. A shared roof slope therefore does not mean identical requirements for the layers beneath it. It is worth marking the functional zones on the plan before discussing the roofing. An attached canopy or open paddock also matters.

By |2026-11-15T18:28:38+01:002021-08-30|Construction basics|Comments Off on Corrugated fibre cement roofing for stables: horse comfort and building maintenance

IKO enertherm ALU TAP with outlets and roof covering

For ALU TAP, the drainage plan should be consistent with the layout of the outlets and the covering details. Changing the position of a drain may require changing the order of the tapered boards. The membrane alone will not restore the intended direction of water flow on a poorly shaped field. The inspection should cover both the geometry and the subsequent sealing. The cross-section under consideration covers a roof with aluminium tapered boards at different pitches. The IKO enertherm ALU TAP task must be described together with the layers adjoining its surface. An important junction point is the joint between fields with a different drainage direction. The basis for agreement is the drainage field plan with marked pitches and heights. Before selecting materials, the height difference between the ends of the tapered board and the length in the direction of fall must be established so that the order of layers has a real reference.

By |2026-11-16T01:36:47+01:002021-08-07|Construction basics|Comments Off on IKO enertherm ALU TAP with outlets and roof covering

Kingspan PIR in roof systems: Therma TR26, TR27 and suitable facings

Kingspan boards are selected by family and application, not by brand alone. Therma TR26 and TR27 have a PIR core, whereas Kooltherm is phenolic foam insulation. The facings also differ: TR26 has an aluminium-containing facing, while TR27 has a glass fibre facing. A substitution requires checking the connection to the covering, the fixing, and the thickness needed to achieve the thermal resistance. In this guide, we separate these criteria from the assessment of load-bearing capacity and fire requirements. We also show why the full product name and documentation of the actual cross-section are needed to compare offers and approve a substitute material.

By |2026-11-16T06:06:44+01:002021-07-24|Construction basics|Comments Off on Kingspan PIR in roof systems: Therma TR26, TR27 and suitable facings

XPS and fire safety in industrial buildings: key distinctions

XPS is a plastic thermal insulation. It should not be presented as a non-combustible material, even when it remains covered by concrete in the finished floor. Extruded polystyrene has a specific reaction to fire, and the building element has its own requirements. These are two different levels of assessment. In an industrial hall, the sequence of works, storage and later changes to installations also matter. Correct selection requires more than checking a single letter on the label. The reaction-to-fire class indicates how the material behaves under specific test conditions. It must be read from the documentation for the specific XPS. There is no basis for attributing an identical class to all boards. Products with different declarations are available on the market, including among materials of a similar colour.

By |2026-11-16T06:07:35+01:002021-07-01|Construction basics|Comments Off on XPS and fire safety in industrial buildings: key distinctions

Flat roof with PIR boards: matching the facing, falls and fixing

Choosing PIR boards for a flat roof starts with the roof build-up as a whole. The type of facing affects bonding, and the fixing method must transfer loads to the substrate. Falls and drainage should be planned at the same time, because they affect the thickness and the detailing of the layer edges. Aluminium laminate, glass fleece and bituminous facing are not interchangeable surfaces. A glass-fleece surface and an aluminium laminate may require different contact layers. Compatibility must be confirmed for the specific type of membrane or roofing felt. The facing is the surface in contact with the next layer, so its type matters in practice.

By |2026-11-16T01:34:44+01:002021-05-22|Construction basics|Comments Off on Flat roof with PIR boards: matching the facing, falls and fixing