Quality checks for swissporPIR Alu: from the substrate to covering the boards

The swissporPIR Alu layer can only fulfil its function if the boards arrive at installation in an appropriate condition. The rigid core and thin facings require protection during transport, storage and cutting. Moisture, dust or a damaged edge change the conditions for making the next joint, even if the marking on the packaging is correct. The guide leads from acceptance of the delivery through preparation of the substrate to the inspection before covering. It also discusses the organisation of the reserve on the roof and the sequence of deliveries. Assessment of the actual thickness, continuity of the core and the contact surface with the next layer supplements the declared parameters of this PIR insulation.

2026-11-16T06:07:02+01:00

Choosing a vapour control layer beneath EPS roof insulation

The vapour control layer under polystyrene is selected to suit the whole roof and the conditions in the rooms. What counts is the resistance to water vapour diffusion, but also the airtightness of the joints. The same membrane does not have to perform equally well above a dry warehouse and a damp back room. The design must specify the particular function of the layer and how its edges and penetrations are to be formed. The layer referred to as a vapour control layer limits the transmission of water vapour by diffusion. Its effectiveness is described by parameters, not by the trade name alone. In many solutions it also helps to provide airtightness. These are two related but different tasks. A material with high diffusion resistance will not fulfil the second of these if the laps have been left open.

2026-11-16T06:08:13+01:00

How does a metallic coating protect steel sheet?

The metallic protective layer in coated steel sheet separates the steel core from its surroundings and, together with the other coatings, helps limit corrosion. When buying, it is most important to establish its type, since this determines the scope of protection rather than colour alone. The specification should distinguish information about the steel, the metallic layer and the organic coating. During installation, edges must be protected, filings removed and approved tools used. Zinc will not protect every scratch indefinitely, so correct detailing and subsequent care also matter.

2026-11-14T16:30:49+01:00

BauderPIR FA beneath waterproofing: rebated edges, support and fixing

The large-format FA board rests on the substrate specified in the roof design. The rebates help to align the joints, but they do not make the boards a self-supporting covering. The support and fixing requirements of the selected system must be observed. The drawing should separate the board layout from the load path into the structure. The BauderPIR FA scope must be described together with the layers adjoining its surface. An important junction detail is the milled edge of the large-format board. The basis for coordination is a row plan based on the effective board dimension. Before selecting materials, the actual coverage area and the widths of the perimeter strips must be determined so that the sequence of layers has a real reference.

2026-11-16T01:36:22+01:00

Would a 40 mm second-grade roof panel suit a small warehouse?

With a small equipment store, it is easy to assume that a thin, cheap roof panel will do in any situation. Yet even a simple roof slope requires proper supports, adequate fall and tight joints. Second-grade material must be assessed according to the type of deviation. A thickness of 40 mm and a low price do not replace information about the specific product and the conditions under which the roof will work. A shed for dry kayaks or folding tables has different requirements from a store for moisture-sensitive materials. Check whether the interior is only meant to shelter from precipitation or to maintain a specific temperature. Planned later conversion into a workshop should also be taken into account from the outset, rather than assuming that insulation can easily be added after installation.

2026-11-14T16:27:50+01:00

How do you ventilate a metal roof?

To ventilate a roof slope covered with metal sheeting, a clear path must be designed from the inlet at the eaves to the outlet at the top of the slope. Readers should check whether, after installation, the actual airflow cross-section has been reduced by a sagging membrane, protruding insulation or undersized counter-battens. The membrane alone does not create air movement, and its vapour permeability does not replace the ventilation gap. It is also worth verifying that inlets and outlets are protected yet still open, and that obstacles on the slope do not interrupt the planned air path.

2026-11-14T19:46:17+01:00

What panel thickness should you choose for a garage roof that is also used as a workspace?

Garages increasingly house a workbench, sports equipment and items that need a dry place. The roof panel thickness should therefore be matched to the building's full function. A different choice may make sense for parking alone than for daily work. The roof must also be checked for loads, water and moisture from the vehicle. For a garage used as a workshop, note the heating time and the expected temperature. If only a car is kept inside, efficient air exchange and protection of stored items may be the priority. If several hours a day are spent at the bench, the comfort of the entire work area matters.

2026-11-14T12:37:36+01:00

swissporPIR Alu and waterproofing: choosing a complete roof assembly

A flat roof with swissporPIR Alu requires the substrate, vapour control layer, PIR boards, fixing and waterproofing to be selected together. The gas-tight laminate protects the core but does not replace a tight covering. According to the instructions for this product, adhesive bonding does not dispense with mechanical fixing. The requirements regarding the dryness of the boards and the design of the drains must also be observed. The guide discusses support on trapezoidal sheet metal, the arrangement of joints, height restrictions at parapets and the details of outlets and equipment. The assessment covers the full cross-section and its terminations, because the generic name polyurethane insulation does not confirm the suitability of a specific combination of roofing materials.

2026-11-16T06:06:59+01:00

Single, double and snap-lock standing seams: how the joints differ

Longitudinal lines on the roof may look similar, although they conceal different connections. A traditional standing seam is formed during roofing work. A click panel has prepared edges that are joined by snap-locking. This choice affects the substrate, fixings and details. Not all such coverings should be treated as one system. The edges of adjacent sheet metal strips are folded over the covering surface and joined by crimping. Single and double standing seams differ in how they are closed. In the double seam, the connection is additionally folded. Execution requires suitable tools and careful preparation of the strips.

2026-11-14T10:14:59+01:00

How to set out modular tile-effect sheets on a pitched roof

Begin planning the layout of modular metal roof tiles by measuring the actual roof slopes, not by counting panels straight away. Check whether the dimensions from the design match the completed structure, because even a small difference changes the width of the last cut. Mark the eaves, ridge, hips, valleys and the actual position of openings. Describe each slope separately and indicate the drawing's viewing side to avoid swapping left and right slopes. Use the effective cover width for the specific model to determine rows and columns, since overall dimensions include overlaps. Also check the position of ribs relative to battens and the possible installation directions allowed by the profile's construction.

2026-11-14T19:47:50+01:00