About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

Which PIR board format will make your renovation easier: 120 × 60 or 120 × 240 cm?

A large board means fewer joints, but in a small flat it can be difficult to bring in and position. A smaller format is easier to fit into recesses, although it creates more joints. When choosing PIR, check more than just the dimensions stated in centimetres. The edge type, the actual coverage area and the way the board is finished also matter. A board with nominal dimensions of 120 × 60 cm has 0.72 m², while 120 × 240 cm has 2.88 m². The large element therefore has four times the nominal area. This does not mean installation is four times faster: it must be carried, fitted and supported in line with the chosen solution.

By |2026-11-14T10:17:31+01:002023-11-06|Construction basics|Comments Off on Which PIR board format will make your renovation easier: 120 × 60 or 120 × 240 cm?

Why a price per square metre tells only part of the cost of a metal tile roof

Two tile-effect metal roofing products can have a similar headline price in the quote, yet a different cost for covering the same roof slope. The reason may be the unit of sale, the number of modules required or the scope of extras. It is therefore worth starting by converting the price to usable surface area. Then check what is actually included in the stated amount. The price may relate to a full sheet metre or an effective covering metre. Part of the sheet is concealed in the laps. It does not create new roof surface, although it is still part of the material purchased. A lower rate per full metre is therefore not necessarily more favourable.

By |2026-11-14T10:14:55+01:002023-11-04|Construction basics|Comments Off on Why a price per square metre tells only part of the cost of a metal tile roof

α-therm ROOF: IDELCO boards for different roof covering systems

IDELCO α-therm ROOF is a PIR board for flat roofs with a gas-tight kraft paper and aluminium laminate on both sides. In such a roof build-up, the insulation is selected together with the substrate, the vapour control layer, the waterproofing and the fixing. The use of ballast, adhesive or fasteners changes the loads and the way the covering is held down, so approval of one method does not confirm the others. The roof detail should also show the terminations at parapets and at service penetrations. This guide explains how to match the parameters of a specific board with the design of these junctions. The general term “polyurethane insulation” identifies neither its facing nor the complete roof system.

By |2026-11-16T06:03:44+01:002023-10-31|Construction basics|Comments Off on α-therm ROOF: IDELCO boards for different roof covering systems

Therma TR27 and waterproofing: choosing insulation for a roof system

Kingspan Therma TR27 is a PIR board with glass fibre facings on both sides. This surface forms the interface with the covering layers, so the selection covers material compatibility, substrate preparation and the way the joint is made. The catalogue describes flat roofs and terraces that are mechanically fixed, bonded or ballasted, in accordance with the system documentation. This does not mean that any adhesive is approved or that it can be swapped for any PIR board. The thermal parameters of TR27 also depend on the thickness. In the following, we separate the requirements relating to the facings, the cut pieces, the loads at equipment and the cost of the complete solution, so that the cross-section corresponds to the actual roof layers.

By |2026-11-16T06:06:38+01:002023-10-27|Construction basics|Comments Off on Therma TR27 and waterproofing: choosing insulation for a roof system

What flashings are needed on a metal roof and how do you calculate their quantity?

Flashings close the edges and guide water through difficult roof areas. A complete set cannot be selected from the roof surface area alone. A plan of edges, roof valleys and penetrations is needed. The easiest approach is to go over the roof on the drawing from the eaves to the ridge. For each section, note its length and purpose. In this zone, water from the covering must be directed into the gutter and the layers below properly terminated. The gutter apron and the fascia cover serve different purposes. Their presence and shape depend on the chosen detail. It is not worth ordering both simply because they have similar names.

By |2026-11-14T10:14:58+01:002023-10-26|Construction basics|Comments Off on What flashings are needed on a metal roof and how do you calculate their quantity?

Metal tile-effect roofing or concrete tiles: what should you compare?

The choice between metal roof tiles and concrete roof tiles depends above all on how well the covering matches the roof structure, not on the price of the basic element alone. Check whether the design or the condition of the existing roof frame allows for the weight of the chosen covering together with the permanent layers and snow and wind loads. In a renovated building, weight is particularly important, so compare the finished covering over the same area, including accessories and flashings. Also consider the roof pitch, substrate requirements and installation method. Leave detailed technical decisions to the designer.

By |2026-11-14T16:29:36+01:002023-10-24|Construction basics|Comments Off on Metal tile-effect roofing or concrete tiles: what should you compare?

When does a 40 mm wall panel actually help reduce costs?

A thin wall panel is sometimes considered for a storage cupboard, seasonal store or partitioning off an area inside a hall. However, savings depend on suitability for the building's function. A 40 mm panel bought for a room that is later to be permanently heated may force costly changes. First establish the requirements, then compare prices. Dry garden equipment, textiles and electronic devices do not have the same requirements. Rain protection alone is not enough for items sensitive to moisture and large temperature fluctuations. Ask whether the store is to be merely enclosed, periodically heated, or maintain constant conditions throughout the winter.

By |2026-11-14T12:35:31+01:002023-10-18|Construction basics|Comments Off on When does a 40 mm wall panel actually help reduce costs?

Pitched roof with Powerroof: membrane, joints and load transfer

In a sloping roof, Powerroof works together with the structure, the protective layer and the components beneath the covering. It cannot be assessed independently of the fixings. The roof slope must simultaneously drain water, transfer loads and maintain the continuity of the insulation at the edges. Recticel Powerroof is a PIR board for above-rafter thermal insulation of sloping roofs. It has an aluminium facing and a tongue-and-groove joint on all four edges. When selecting PIR boards for the system, draw the above-rafter Powerroof layer running over the timber structure of the sloping roof in the actual cross-section. Powerroof must be run over the rafters while maintaining correct fixing of the entire covering, because the remaining layers must fit the same solution. The individual layers must work together, because continuous insulation does not replace the components that transfer forces from the covering to the structure.

By |2026-11-16T01:35:45+01:002023-10-12|Construction basics|Comments Off on Pitched roof with Powerroof: membrane, joints and load transfer

XPS beneath floors used by pallet trucks

A pallet truck has small wheels, yet it can still carry a heavy load. For the floor, this means localised pressure and repeated movement. XPS under such a floor is selected together with the load-bearing layer, not on the basis of the truck weight stated in the offer. Extruded polystyrene can combine insulation performance with resistance to load. The prerequisite is knowledge of the actual operating conditions and verification of the entire floor assembly. The calculation requires the mass of the vehicle and of the goods being transported. The wheel spacing, the number of wheels and the way the pressure is transferred to the substrate are important. Two trucks with a similar load capacity do not necessarily load the floor in the same way.

By |2026-11-16T06:07:18+01:002023-10-12|Construction basics|Comments Off on XPS beneath floors used by pallet trucks

PIR in warm roofs and XPS in inverted roofs: why the distinction?

When comparing roof insulation, the order of the layers must first be established. PIR beneath the waterproofing and XPS in a suitable inverted roof do not perform the same function. Only once the build-up has been identified can the parameters be compared. PIR boards are particularly valuable where high thermal resistance is needed within a limited height. For illustrative thermal conductivities of 0.022 and 0.035 W/(m·K), 100 mm of the first material provides approximately the same thermal resistance as 159 mm of the second. This is an illustration of the calculation, not a fixed rule for replacing PIR with XPS. In practice, the available thicknesses are selected and the values declared for the finished product are checked. At a parapet or an existing roof threshold, a few centimetres can determine the scope of the conversion.

By |2026-11-16T01:34:26+01:002023-10-08|Construction basics|Comments Off on PIR in warm roofs and XPS in inverted roofs: why the distinction?