About PiVi

This author has not yet filled in any details.
So far PiVi has created 1593 blog entries.

Energy refurbishment of an urban commercial building: planning a new envelope

An energy refurbishment of an urban commercial building should combine improvements to the building envelope with the organisation of entrances, deliveries and the operation of building services. Sandwich panels and PIR insulation may be used in different parts of the renovation, but each requires separate selection. The new wall must fit the existing supports and openings, and the roof layers must suit the drainage and the way the roof is used. On Sandwich-panel.pl we discuss how to prepare such a project, from surveying the building to verifying the results. We do not assume a single solution for every retail pavilion or workshop. The scope of works should follow from the condition of the building and the needs of the tenants; opening gates, ventilation and operating hours can significantly affect the energy performance.

By |2026-11-15T18:27:11+01:002022-05-13|Construction basics|Comments Off on Energy refurbishment of an urban commercial building: planning a new envelope

Steel sections around doors and rooflights when refurbishing a building envelope

A regular support grid works well over large wall and roof areas. The places where this grid is interrupted require more attention. A door, skylight or new opening for a service changes the way loads are transferred. Cold-formed profiles help create the necessary framing, but their selection must suit the new situation. In such details it is particularly important to combine structural knowledge with the documentation of the building envelope. To prepare the steel, structural dimensions are needed as well as the position of the opening relative to the building axis. The requirements of the equipment or joinery must also be known. A door may need space for tracks and its own fixing points. A skylight requires correct support and flashings.

By |2026-11-15T18:24:57+01:002022-05-10|Construction basics|Comments Off on Steel sections around doors and rooflights when refurbishing a building envelope

Timber connectors for roof structures – what each connection has to do

The choice of carpentry connection is determined by the direction and value of forces at the node, not by the appearance of the fastener alone. Check whether the design specifies the required components, their number and layout, and whether the selected fasteners match the documentation. Pay attention to the geometry of notches and cuts, the condition of the wood around fixings, and protection against moisture. During renovation, compare the actual arrangement with the design, including unapproved holes and missing fixings. A substitute should have demonstrated conformity, not just a similar shape.

By |2026-11-15T03:30:37+01:002022-05-06|Construction basics|Comments Off on Timber connectors for roof structures – what each connection has to do

Tile-effect metal roofing or clay tiles – which suits the roof?

The choice between metal roofing tiles and ceramic tiles should follow from the roof design and a full quotation, not from appearance or the price of a single element. Above all, check the actual weight of the covering per square metre, because ceramic is considerably heavier than typical metal sheeting, and comparing individual pieces can be misleading. For a renovation, verify the existing roof structure and supports; in a new build, match the structure to the chosen system. Also consider roof pitch, ventilation and the requirements for the underlay.

By |2026-11-14T19:46:15+01:002022-05-03|Construction basics|Comments Off on Tile-effect metal roofing or clay tiles – which suits the roof?

Does a white PIR board 100 mm long and 2480 mm fit a small room?

A short white PIR wall board 100 mm can be convenient when partitioning a back room or a small workshop. However, colour and dimension alone do not determine suitability. The 2480 mm length must be compared with the actual installation height, and second grade with the description of the specific defect. An offer labelled in this way requires several separate checks. Start with a section through the floor, wall and ceiling. The usable height depends on finish levels, construction and how the panel is closed at the top and bottom. A 2480 mm length does not promise a room of exactly that height. Do not order quantities based solely on a measurement from the raw floor to the ceiling.

By |2026-11-14T12:35:16+01:002022-04-29|Construction basics|Comments Off on Does a white PIR board 100 mm long and 2480 mm fit a small room?

How to fit out a loft with sloping ceilings while preserving its insulation

Start by determining where the heated space ends and what lies beneath the sloping ceiling finish. This decides whether a wardrobe, light fitting or socket will breach the airtight layer or weaken the insulation. In an existing attic, make local openings; in a new house, keep photographs taken before the lining went up. Resolve stains, cold corners and any smell of damp before ordering furniture. Match the design to the insulation and frame thickness.

By |2026-11-14T19:54:51+01:002022-04-19|Construction basics|Comments Off on How to fit out a loft with sloping ceilings while preserving its insulation

What are the advantages and limitations of mineral wool panels in everyday use?

A mineral wool panel combines steel surfaces with a fibrous core. This construction can be a good choice for a workshop, warehouse or back-of-house area. It does not, however, remove the need for design or attention to detail. It is worth assessing it by its everyday effects: ease of cleaning, noise protection, heating cost and weight during installation. Both sides of the panel form finished surfaces. In a dry workshop, no additional layers are needed just to achieve a standard wall enclosure. This simplifies planning and reduces the number of wet processes. The appearance remains technical, which is worth accepting before ordering.

By |2026-11-14T10:15:43+01:002022-04-12|Construction basics|Comments Off on What are the advantages and limitations of mineral wool panels in everyday use?

termPIR WS and waterproofing: choosing a compatible flat roof build-up

What comes into contact with the membrane or the adhesive affects how the roof system performs. In termPIR WS this is the glass fleece. For this reason, the thermal parameters must be read together with the requirements of the waterproofing, the method of fixing and the documentation of the relevant system. termPIR WS consists of a PIR core with a gas-permeable glass fleece facing on both sides. This is a different surface from a gas-tight aluminium laminate. When selecting PIR boards for a system, draw the surface of the flat roof on which the board facing is to work together with the covering in the actual cross-section. The termPIR WS fleece must be linked to the layers and the fixing method of the adopted roof covering, because the remaining layers must match the same solution.

By |2026-11-16T01:35:07+01:002022-04-08|Construction basics|Comments Off on termPIR WS and waterproofing: choosing a compatible flat roof build-up

How a hipped roof works and what affects its cost

A hipped roof has four slopes and does not require classic gable walls at both ends of the building. Its cost results from the structure, the covering area and the number of corners and cut-offs. Choosing lightweight sheet metal may reduce part of the load, but it does not remove the complexity of the geometry. The estimate should cover the entire roof, together with flashings and drainage. It is worth checking whether the offer includes a sheet layout plan, separate quantities of materials and how waste is settled. Comparison should be based on a complete set of drawings and layer specification, not just the price per square metre.

By |2026-11-14T19:45:52+01:002022-03-28|Construction basics|Comments Off on How a hipped roof works and what affects its cost

How to reduce roofing costs for a house, shelter or garage

The cost of a roof is reduced above all by matching the solution to the building's function, not by choosing the cheapest sheet metal. Over a heated house, thermal insulation, internal airtightness and acoustic comfort are needed; over an open shelter, protection from precipitation, structure and condensate drainage matter. Before pricing, describe the planned use, because an unheated garage, a heated one or a workshop that is periodically humid require different assemblies. Then compare complete variants including cutting layout, transport and labour, checking that simpler geometry does not omit necessary layers, flashings and fixings. Leave design decisions to the designer.

By |2026-11-14T19:47:24+01:002022-03-22|Construction basics|Comments Off on How to reduce roofing costs for a house, shelter or garage